Mercury 2010 Milan Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 330

background image

To adjust the head restraint, do the following:

1. Raise the head restraint by
pulling up on the head restraint.

2. Lower the head restraint by
pressing and holding the guide
sleeve adjust/release button and
pushing down on the head restraint.

Properly adjust the head restraint so that the top of the head restraint is
even with the top of your head and positioned as close as possible to the
back of your head. For occupants of extremely tall stature, adjust the
head restraint to its full up position.

WARNING:

The adjustable head restraint is a safety device.

Whenever possible it should be installed and properly adjusted

when the seat is occupied.

Seating and Safety Restraints

114

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
112
113
114
115
116
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: DANA Страницы: 42

Бренд: dallara Страницы: 37

Бренд: Yakima Страницы: 8

Бренд: Hama Страницы: 6

Бренд: Vauxhall Страницы: 2

Бренд: PEUGEOT Страницы: 128

Бренд: Schumacher Electric Страницы: 87

2009 ESCALADE ESV

Бренд: Cadillac Страницы: 602

Бренд: Vintage Air Страницы: 28

Бренд: CITROEN Страницы: 52

Бренд: Actia Страницы: 37

Бренд: Kargo Master Страницы: 6

Car Cup Holder Phone Mount

Бренд: UGREEN Страницы: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Бренд: Audiovox Страницы: 14

Бренд: Porsche Страницы: 313

Vehicle Asset Communicator

Бренд: I.D. Systems Страницы: 41

Бренд: Bestop Страницы: 31

Бренд: Oypla Leisure Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды