Mercury 2010 Milan Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 330

background image

Please read and understand the
entire procedure before you begin.

1. Insert the first previously
programmed

coded key

into the

ignition.

2. Turn the ignition from the 1 (off)
position to the 3 (on) position. Keep
the ignition in the 3 (on) position
for at least three seconds, but no more than 10 seconds.

3. Turn the ignition to the 1 (off) position and remove the first

coded

key

from the ignition.

4. After three seconds but within 10 seconds of turning the ignition to
the 1 (off) position, insert the second previously

coded key

into the

ignition.

5. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep
the ignition in the 3 (on) position for at least three seconds, but no more
than 10 seconds.

6. Turn the ignition to the 1 (off) position and remove the second
previously programmed

coded key

from the ignition.

7. After three seconds but within 20 seconds of turning the ignition to
the 1 (off) position and removing the previously programmed

coded

key,

insert the new unprogrammed key (new key/valet key) into the

ignition.

8. Turn the ignition from the 1 (off) position to the 3 (on) position. Keep
the ignition in the 3 (on) position for at least six seconds.

9. Remove the newly programmed

coded key

from the ignition.

If the key has been successfully programmed it will start the vehicle’s
engine and will operate the remote entry system (if the new key is an
integrated keyhead transmitter). The theft indicator light will illuminate
for three seconds and then go out to indicate successful programming.

If the key was not successfully programmed, it will not start your
vehicle’s engine and/or will not operate the remote entry features. The
theft indicator light may flash on and off. Wait 20 seconds and you may
repeat Steps 1 through 8. If failure repeats, bring your vehicle to your
authorized dealer to have the new key(s) programmed.

To program additional new unprogrammed key(s), wait 20 seconds and
then repeat this procedure from Step 1.

Locks and Security

102

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
100
101
102
103
104
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Panasonic Страницы: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 12

Бренд: Harmar Mobility Страницы: 10

AUDI 4G HIGHEND

Бренд: KAP Страницы: 20

Reference Series

Бренд: OEM Audio Страницы: 29

CommCenter D1 Series

Бренд: Federal Signal Corporation Страницы: 16

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: Quadratec Страницы: 8

Бренд: Menabo Страницы: 12

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Truck Training Model

Бренд: WABCO Страницы: 56

Бренд: TEINHOF Страницы: 2

RearSight 250-8308

Бренд: Rostra Страницы: 2

Бренд: APS Страницы: 3

Бренд: Kia Страницы: 680

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды