Mercury 2010 Milan Скачать руководство пользователя страница 63

Страница: 63 / 330

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Replacing headlamp bulbs

High beam/low beam bulb replacement

For driver side replacement of this bulb, do the following:

WARNING:

To reduce the risk of vehicle damage and/or

personal burn injuries do not start your engine with the air

cleaner removed and do not remove it while the engine is running.

1. Release the clamps that secure the air filter housing cover. See

Changing the air filter element

in the

Maintenance & Specifications

section for more information.

2. Carefully separate the two halves of the air filter housing.

3. Locate the mass air flow sensor electrical connector on the air outlet
tube. This connector will need to be unplugged.

4. Remove the air filter assembly.

5. Remove the rubber headlamp bulb access cover.

6. Remove the bulb socket by
rotating it counterclockwise, then
pull it straight out of the lamp
assembly.

7. Disconnect the electrical connector.

To install, reverse the removal procedure.

Lights

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды