Mercury 2010 Milan Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 330

background image

7. Remove the jack and fully tighten
the lug nuts in the order shown.
Refer to

Wheel lug nut torque

specifications

later in this chapter

for the proper lug nut torque
specification.

8. Unblock the wheels.

Stowing the wheel and jack

1. Fully collapse the jack and place it back in the storage area in the
trunk.

2. Replace the jack retention bolt to secure the jack.

3. Place the tire in the storage bin in the trunk.

4. Replace the cover plate and bolt.

•

When storing a flat road tire, flip the cover plate over and use the long
bolt.

•

When storing the temporary spare tire, replace the cover plate and
use the short bolt.

5. Secure the bolt using the lug wrench.

6. Insert the lug wrench and bolt in the tool bag and place over the jack.

7. Replace the carpeted load floor panel.

WHEEL LUG NUT TORQUE SPECIFICATIONS

Retighten the lug nuts to the specified torque at 500 miles (800 km)
after any wheel disturbance (tire rotation, changing a flat tire, wheel
removal, etc.).

Bolt size

Wheel lug nut torque*

ft-lb

N

•

m

M12 x 1.5

100

135

* Torque specifications are for nut and bolt threads free of dirt and
rust. Use only Ford recommended replacement fasteners.

1

4

3

2

5

Roadside Emergencies

249

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
247
248
249
250
251
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Daihatsu Страницы: 485

Бренд: Toyota Страницы: 529

Бренд: Aries Страницы: 3

Бренд: Romik Страницы: 6

Бренд: Victory 4x4 Страницы: 13

Бренд: FormFit Страницы: 4

Бренд: Mazda Страницы: 720

Бренд: Subaru Страницы: 99

Бренд: Uebler Страницы: 56

Бренд: Ford Страницы: 256

Бренд: Ford Страницы: 256

Бренд: Motoalliance Страницы: 4

Бренд: VP Autoparts Страницы: 2

Бренд: Volvo Страницы: 286

Turnoverball 1020

Бренд: Bowers & Wilkins Страницы: 6

Бренд: Blitz Страницы: 4

1997 Park Avenue

Бренд: Buick Страницы: 420

Бренд: ULTIMATE SPEED Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды