Mercury 2010 Milan Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 330

background image

Replacing front side marker bulbs

1. Make sure the headlamp control
is in the off position.

2. From underneath the vehicle,
partially remove the tire splash
shield by removing the press pins.
After removing to allow free access
to the front side marker lamp bulb
and electrical wire harness, the
splash shield should be able to be
repositioned.

3. Rotate the lamp clockwise while holding the electrical connector in
place. After rotating the lamp 90 degrees clockwise, pull and disengage
the wire harness and bulb from the lamp.

4. With the bulb exposed, carefully
remove the bulb from the socket by
grasping the bulb and pulling it
away from the wire harness.

Replace with a new bulb, and reverse the removal steps to complete the
process.

Replacing stop/tail/turn/and side marker bulbs

Your vehicle is equipped with a rear lamp that has a stop/tail and side
marker lamp module containing integral multiple light emitting diodes
(LED). If one or more LEDs burn out, the complete lamp module has to
be replaced. See your authorized dealer for the replacement lamp.

Replacing rear turn signal bulbs

1. Make sure the headlamp switch is in the off position and open the trunk.

2. Lift out trunk floor carpeting panel to access a luggage scuff plate
(hard molding) shingles and a trunk side panel (dark grey, soft
wheelhouse side trim panel) at the lamp area.

3. Carefully pull/push the trunk side panel (dark grey, soft wheelhouse
side trim panel) outboard to expose the lamp assembly. The most

Lights

66

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
64
65
66
67
68
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Hama Страницы: 2

Бренд: Abarth Страницы: 36

Бренд: Aries Страницы: 3

Бренд: iDataLink Страницы: 99

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

Ride-Rite Air Helper Springs 2173

Бренд: Firestone Страницы: 4

Бренд: ideus Страницы: 159

Бренд: Hank Страницы: 2

Бренд: Toyota Страницы: 636

Бренд: Meta System Страницы: 16

Бренд: Simplicity Страницы: 10

Бренд: Brodit Страницы: 2

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Бренд: Connects2 Страницы: 8

Бренд: SAAS Страницы: 3

Бренд: Nuna Страницы: 29

Бренд: Hamron Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды