Mercury 2010 Milan Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 330

background image

must complete Steps 1–5 within 30 seconds or the procedure will have
to be repeated. If the procedure needs to be repeated, wait a minimum
of 30 seconds before beginning again.

1. Place the key in the ignition and
turn the ignition to the 3 (on)
position.

2. Press the power door unlock
control on the door panel three
times.

3. Turn the ignition from the 3 (on)
position to the 1 (off) position.
4. Press the power door unlock control on the door panel three times.
5. Turn the ignition back to the 3 (on) position. The horn will chirp one
time to confirm programming mode has been entered and is active.
6. Press the power door unlock control twice within five seconds.

Note:

The horn will chirp once to indicate the perimeter lighting feature

has been deactivated. The horn will chirp once and honk once (one short
and one long) to indicate the perimeter lighting feature has been activated.
7. Turn the ignition to the 1 (off) position to exit the procedure.

Note:

The horn will chirp once to confirm the procedure is complete.

Illuminated exit

•

When all vehicle doors are closed and the key is removed from the
ignition, the interior lamps and the puddle lamps (if equipped) will
illuminate.

The lamps will turn off if all the doors remain closed and

•

25 seconds elapse, or

•

the key is inserted in the ignition.

Battery saver

The battery saver will shut off the lamps 30 minutes after the ignition
has been turned to the 1 (off) position.

•

If the dome lamps were turned on using the panel dimmer control, the
battery saver will shut them off 30 minutes after the ignition has been
turned to the off position.

•

If the courtesy lamps were turned on because one of the vehicle doors
or the trunk was opened, the battery saver will shut off them off
10 minutes after the ignition has been turned to the off position.

•

The battery saver will shut off the headlamps 10 minutes after the
ignition has been turned to the off position.

Locks and Security

97

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
95
96
97
98
99
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Vauxhall Страницы: 2

Бренд: Jabra Страницы: 2

Бренд: Jabra Страницы: 38

Бренд: Warrior Products Страницы: 2

Бренд: DAVIS Страницы: 32

Бренд: EEZ RV Страницы: 31

Бренд: Gator Страницы: 8

2004 Vibe Navigation System

Бренд: Pontiac Страницы: 44

Бренд: Beper Страницы: 52

Бренд: JBL Страницы: 12

Бренд: Thule Страницы: 8

Escalade 2004 Escalade ESV

Бренд: Cadillac Страницы: 472

Бренд: Volvo Страницы: 18

Бренд: Calix Страницы: 4

Бренд: Air Lift Страницы: 12

Бренд: BMW Страницы: 242

Бренд: OEM Audio Страницы: 21

Бренд: Intellitronix Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды