Mercury 2010 Milan Скачать руководство пользователя страница 295 | Manualshive

Страница: 295 / 330

background image

Easy Fuel™ “no cap” fuel system

Your fuel tank is equipped with an Easy Fuel™ “no cap” fuel filler
system. This allows you to simply open the fuel filler door and insert the
fuel filler nozzle into the fuel system. The Easy Fuel™ system is
self-sealing and protected against dust, dirt, water and snow/ice.

When fueling your vehicle:

1. Turn the engine off.

2. Open the fuel filler door.

3. Slowly insert the fuel filler nozzle fully into the fuel system. Pump fuel
as normal.

4. After you are done pumping fuel, slowly remove the fuel filler
nozzle—allow about five seconds after pumping fuel before removing the
fuel filler nozzle. This allows residual fuel to drain back into the fuel tank
and not spill onto the vehicle.

Note:

A fuel spillage concern may occur if overfilling the fuel tank. Do

not overfill the tank to the point that the fuel is able to bypass the fuel
filler nozzle. The overfilled fuel may run down the drain located below
and in front of the fuel filler door.

If the check fuel fill inlet lamp or CHECK FUEL FILL INLET message
comes on, the fuel fill inlet may not have properly closed. The inlet may
have stuck open or debris may be preventing the inlet from fully closing.
At the next opportunity, safely pull off the road, turn off the engine,
open the fuel filler door and remove any visible debris from the fuel fill
opening. Insert either the fuel fill nozzle or the fuel fill funnel (see

Refilling with a portable fuel container

for funnel location) provided

with the vehicle several times to dislodge any debris and/or allow the
inlet to close properly. If this action corrects the problem, the check fuel
fill inlet lamp or CHECK FUEL FILL INLET message may not reset
immediately. It may take several driving cycles for the check fuel fill inlet
lamp or CHECK FUEL FILL INLET message to turn off. A driving cycle
consists of an engine start-up (after four or more hours with the engine
off) followed by city/highway driving. Continuing to drive with the check
fuel fill inlet lamp or CHECK FUEL FILL INLET message on may cause
the service engine soon lamp to turn on as well.

WARNING:

The fuel system may be under pressure. If you hear

a hissing sound near the fuel filler door (Easy Fuel™ “no cap”

fuel system), do not refuel until the sound stops. Otherwise, fuel may
spray out, which could cause serious personal injury.

Maintenance and Specifications

295

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
293
294
295
296
297
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Falcon Страницы: 8

Бренд: Hama Страницы: 40

WrapAround Windjammer

Бренд: Bestop Страницы: 7

Бренд: iArmor Страницы: 4

Бренд: Motoalliance Страницы: 8

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: Thule Страницы: 8

Бренд: Ecco Страницы: 9

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

Bluetooth Phone System 2010

Бренд: Kia Страницы: 16

1995 Cutlass Supreme

Бренд: Oldsmobile Страницы: 340

Бренд: Skoda Страницы: 2

Бренд: Z Flash Страницы: 4

Бренд: Ford Страницы: 256

Turbocharger 15012

Бренд: Edelbrock Страницы: 1

Yukon XL Denali 2015

Бренд: GMC Страницы: 439

Бренд: MacNeil Страницы: 2

Бренд: Buick Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды