Mercury 2010 Milan Скачать руководство пользователя страница 180

Страница: 180 / 330

Additional information contained on the tire sidewall for “LT” type
tires

“LT” type tires have some additional
information beyond those of “P”
type tires; these differences are
described below.

Note:

Tire Quality Grades do not

apply to this type of tire.

LT:

Indicates a tire, designated by

the Tire and Rim Association
(T&RA), that is intended for service
on light trucks.

Load Range/Load Inflation

Limits:

Indicates the tire’s

load-carrying capabilities and its
inflation limits.

Maximum Load Dual lb (kg) at psi (kPa) cold:

Indicates the

maximum load and tire pressure when the tire is used as a dual; defined
as four tires on the rear axle (a total of six or more tires on the vehicle).

Maximum Load Single lb (kg) at psi (kPa) cold:

Indicates the

maximum load and tire pressure when the tire is used as a single;
defined as two tires (total) on the rear axle.

Tires, Wheels and Loading

180

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды