Mercury 2010 Milan Скачать руководство пользователя страница 71

Страница: 71 / 330

TILT/TELESCOPE STEERING WHEEL

To adjust the steering wheel:

1. Pull the lever down to unlock the
steering column.

2. While the lever is in the down
position, move the steering wheel
up or down and in or out until you
find the desired position.

3. While holding the steering wheel
in place, pull the lever up to its
original position to lock the steering
column.

WARNING:

Never adjust the steering wheel when the vehicle is

moving.

ILLUMINATED VISOR MIRROR

Lift the mirror cover to turn on the
visor mirror lamps.

Slide-on-rod feature

Rotate the visor towards the side
window and extend it rearward for
additional sunlight coverage.

Note:

To stow the visor back into

the headliner, visor must be
retracted before moving it back
towards the windshield.

Driver Controls

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды