Mercury 2010 Milan Скачать руководство пользователя страница 244 | Manualshive

Страница: 244 / 330

background image

the

Tires, Wheels and Loading

chapter. Replace the spare tire with a road

tire as soon as possible. During repairing or replacing of the flat tire, have
the authorized dealer inspect the TPMS sensor for damage.

WARNING:

The use of tire sealants may damage your tire

pressure monitoring system and should not be used.

WARNING:

Refer to

Tire pressure monitoring system (TPMS)

in the

Tires, Wheels and Loading

chapter for important

information. If the tire pressure monitor sensor becomes damaged, it
will no longer function.

Dissimilar spare tire/wheel information

WARNING:

Failure to follow these guidelines could result in an

increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare tire/wheel, then it is intended for
temporary use only. This means that if you need to use it, you should
replace it as soon as possible with a road tire/wheel that is the same size
and type as the road tires and wheels that were originally provided by
Ford. If the dissimilar spare tire or wheel is damaged, it should be
replaced rather than repaired.

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that
is different in brand, size or appearance from the road tires and wheels
and can be one of three types:

1.

T-type mini-spare:

This spare tire begins with the letter “T” for tire

size and may have “Temporary Use Only” molded in the sidewall

2.

Full-size dissimilar spare with label on wheel:

This spare tire has

a label on the wheel that states: “THIS TIRE AND WHEEL FOR
TEMPORARY USE ONLY”

When driving with one of the dissimilar spare tires listed above,

do not:

•

Exceed 50 mph (80 km/h)

•

Load the vehicle beyond maximum vehicle load rating listed on the
Safety Compliance Label

•

Tow a trailer

•

Use snow chains on the end of the vehicle with the dissimilar spare
tire

Roadside Emergencies

244

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
242
243
244
245
246
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: RaceChip Страницы: 20

Бренд: Yakima Страницы: 4

Reference Series

Бренд: OEM Audio Страницы: 29

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 2

Бренд: Yakima Страницы: 12

Бренд: TBC Страницы: 12

Бренд: Haibang Страницы: 6

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Transit Vancouver Wagon

Бренд: Webasto Страницы: 44

1973 Convertible

Бренд: Volkswagen Страницы: 80

Бренд: Phonocar Страницы: 2

Autostacker PL-6SR

Бренд: BendPak Страницы: 104

Бренд: Cadillac Страницы: 409

Бренд: Fortin Страницы: 9

Бренд: DriveRight Страницы: 16

Бренд: Lexus Страницы: 830

1500 CLASSIC 2020

Бренд: RAM Страницы: 360

Бренд: Buick Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды