Mercury 2010 Milan Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 330

background image

When inflating your tires

When putting air into your tires (such as at a gas station or in your
garage), the Tire Pressure Monitoring System may not respond
immediately to the air added to your tires.

It may take up to two minutes of driving over 20 mph (32 km/h) for the
light to turn OFF after you have filled your tires to the recommended
inflation pressure.

How temperature affects your tire pressure

The Tire Pressure Monitoring System (TPMS) monitors tire pressure in
each pneumatic tire. While driving in a normal manner, a typical
passenger tire inflation pressure may increase approximately 2 to 4 psi
(14 to 28 kPa) from a cold start situation. If the vehicle is stationary
over night with the outside temperature significantly lower than the
daytime temperature, the tire pressure may decrease approximately 3 psi
(21 kPa) for a drop of 30°F (17°C) in ambient temperature. This lower
pressure value may be detected by the TPMS as being significantly lower
than the recommended inflation pressure and activate the TPMS warning
for low tire pressure. If the low tire pressure warning light is ON, visually
check each tire to verify that no tire is flat. (If one or more tires are flat,
repair as necessary.) Check air pressure in the road tires. If any tire is
under-inflated, carefully drive the vehicle to the nearest location where
air can be added to the tires. Inflate all the tires to the recommended
inflation pressure.

SNOW TIRES AND CHAINS

WARNING:

Snow tires must be the same size, load index, speed

rating as those originally provided by Ford. Use of any tire or

wheel not recommended by Ford can affect the safety and performance
of your vehicle, which could result in an increased risk of loss of vehicle
control, vehicle rollover, personal injury and death. Additionally, the use
of non-recommended tires and wheels could cause steering, suspension,
axle or transfer case/power transfer unit failure.

The tires on your vehicle have all weather treads to provide traction in
rain and snow. However, in some climates, you may need to use snow
tires and chains. If you need to use chains, it is recommended that steel
wheels (of the same size and specifications) be used, as chains may chip
aluminum wheels.

Tires, Wheels and Loading

186

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
184
185
186
187
188
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: VEAP SHIELD UNITED Страницы: 3

Бренд: Front Runner Страницы: 5

Бренд: Ford Страницы: 2

Бренд: CITROEN Страницы: 52

Бренд: AMP Research Страницы: 12

Half Size Trunk Box Organizer C-TBO-CV

Бренд: Havis-Shields Страницы: 1

Бренд: Volvo Страницы: 8

Бренд: Trailboss Страницы: 8

Бренд: Safe Fleet Страницы: 11

Бренд: Camec Страницы: 19

Бренд: TATA Motors Страницы: 136

Бренд: Ford Страницы: 8

Бренд: Intec Страницы: 16

Бренд: Velleman Страницы: 12

OCTAVIA - TECHNICAL CHANGES 11-2009

Бренд: Skoda Страницы: 16

Бренд: Caraudio-Systems Страницы: 9

Бренд: Discount Car Stereo Страницы: 8

Бренд: Mitsubishi Страницы: 362

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды