Mercury 2010 Milan Скачать руководство пользователя страница 236 | Manualshive

Страница: 236 / 330

background image

FUEL PUMP SHUT-OFF

In the event of a moderate to severe collision, this vehicle is equipped
with a fuel pump shut-off feature that stops the flow of fuel to the
engine. Not every impact will cause a shut-off.

Should your vehicle shut off after a collision due to this feature, you may
restart your vehicle by doing the following:

1. Turn the ignition switch to the off position.

2. Turn the ignition switch to the on position.

In some instances the vehicle may not restart the first time you try to
restart and may take one additional attempt.

WARNING:

Failure to inspect and if necessary repair fuel leaks

after a collision may increase the risk of fire and serious injury.

Ford Motor Company recommends that the fuel system be inspected
by an authorized dealer after any collision.

FUSES AND RELAYS

Fuses

If electrical components in the
vehicle are not working, a fuse may
have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any electrical
components.

Note:

Always replace a fuse with one that has the specified amperage

rating. Using a fuse with a higher amperage rating can cause severe wire
damage and could start a fire.

15

Roadside Emergencies

236

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
234
235
236
237
238
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: femkes Страницы: 7

Бренд: Fiat Страницы: 24

Бренд: Valeo Страницы: 28

Бренд: Subaru Страницы: 298

Бренд: Flash Cover Страницы: 2

Бренд: Porsche Страницы: 98

Бренд: Black+Decker Страницы: 21

Бренд: Beeper Страницы: 20

FABIA II TMB PS 035

Бренд: Skoda Страницы: 16

Бренд: r.LiNK Страницы: 21

Бренд: Toyota Страницы: 672

Бренд: Axxess Страницы: 8

Бренд: Ford Страницы: 264

Бренд: TracRac Страницы: 6

Бренд: Beeper Страницы: 2

Бренд: Vauxhall Страницы: 310

Бренд: Whispbar Страницы: 17

Бренд: Snapper Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды