Mercury 2010 Milan Скачать руководство пользователя страница 108

Страница: 108 / 330

WARNING:

To minimize the risk of neck injury in the event of a

crash, head restraints must be installed properly.

Using the manual lumbar support (if equipped)

The lumbar control is located on the
side of the seat cushion.

Turn to adjust lumbar support.

Adjusting the front manual seat (if equipped)

WARNING:

Never adjust the driver’s seat or seatback when the

vehicle is moving.

WARNING:

Always drive and ride with your seatback upright

and the lap belt snug and low across the hips.

Lift handle to move seat forward or
backward.

Seating and Safety Restraints

108

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды