Mercury 2010 Milan Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 330

background image

High beams

Push the lever toward the
instrument panel to activate. Pull
the lever toward you to deactivate.

Flash-to-pass

Pull toward you slightly to activate
and release to deactivate.

PANEL DIMMER CONTROL

Use to adjust the brightness of the
instrument panel and all applicable
lit components in the vehicle during
headlamp and parking lamp
operation.

•

Tap the top or bottom of the
control to brighten/dim all interior
lit components incrementally, or

•

Press and hold at the first position the top or bottom of the control
until the desired lighting level is reached.

•

Press and hold the top of the control to the full on position to activate
the “dome on” feature. This will turn on the interior courtesy lights.
The lights will remain on until the bottom of the control is pressed.

Note:

If the battery is disconnected, discharged, or a new battery is

installed, the dimmer control requires re-calibration. Press the dimmer
control from the full dim position to the full on position to reset. This
will ensure that your displays are visible under all lighting conditions.

OFF

Lights

58

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
56
57
58
59
60
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: VEAP SHIELD UNITED Страницы: 3

Бренд: RAM Commercial Страницы: 12

Бренд: GMC Страницы: 20

Бренд: Camcar Страницы: 2

Бренд: Whispbar Страницы: 15

Бренд: Actia Страницы: 37

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

PRIME DESIGN VRR-E-PM21

Бренд: Safe Fleet Страницы: 12

Бренд: Mercedes-Benz Страницы: 39

Quantum Wash'n'Wipe N30208

Бренд: National Cycle Страницы: 12

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

Бренд: Calix group Страницы: 4

Бренд: Curt Manufacturing Страницы: 4

Бренд: Whispbar Страницы: 112

Бренд: Mazda Страницы: 1001

Бренд: FIRRAK Страницы: 12

Бренд: Conrad Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды