Mercury 2010 Milan Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 330

background image

The fact that the airbags did not inflate in a collision does not mean that
something is wrong with the system. Rather, it means the forces were
not of the type sufficient to cause activation. Side airbags are designed
to inflate in side-impact collisions, not roll-over, rear-impact, frontal or
near-frontal collisions, unless the collision causes sufficient lateral
deceleration.

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side

airbag has deployed,

the

airbag will not function again.
The side airbag system
(including the seat) must be
inspected and serviced by an
authorized dealer.

If the airbag

is not replaced, the unrepaired
area will increase the risk of injury
in a collision.

Determining if the system is operational

The SRS uses a readiness light in the instrument cluster or a tone to
indicate the condition of the system. Refer to the

Warning lights and

chimes

section in the

Instrument Cluster

chapter. Routine maintenance

of the airbag is not required.

Any difficulty with the system is indicated by one or more of the
following:

•

The readiness light (same light as used for front airbag system) will
either flash or stay lit.

•

The readiness light will not illuminate immediately after ignition is
turned to the on position.

•

A series of five beeps will be heard. The tone pattern will repeat
periodically until the problem and light are repaired.

If any of these things happen, even intermittently, have the SRS serviced
at an authorized dealer immediately. Unless serviced, the system may not
function properly in the event of a collision.

Seating and Safety Restraints

143

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
141
142
143
144
145
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: LaserTrack Страницы: 12

Бренд: Warrior Winches Страницы: 17

1306 RAPID SYSTEM

Бренд: Thule Страницы: 8

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: BGS technic Страницы: 5

Бренд: Oldsmobile Страницы: 344

Бренд: ABL Страницы: 66

Бренд: Lexus Страницы: 369

Бренд: Mountain Top Страницы: 12

Бренд: Saab Страницы: 445

Бренд: Yakima Страницы: 21

Бренд: RAM Страницы: 76

Бренд: Advantech Страницы: 59

Бренд: Motoalliance Страницы: 5

Бренд: Cadillac Страницы: 20

Бренд: Saab Страницы: 9

Бренд: Rugged Ridge Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды