Mercury 2010 Milan Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 330

background image

To reinstall the head restraint, line
the posts up in the holes on the seat
back with the head restraint strap
facing the outside of the vehicle and
push down until the head restraint
locks into place. Lift gently to
ensure it is locked into place.

Refer to

Rear adjustable head restraints

earlier in this chapter for

more information.

WARNING:

If the head restraint has been removed from a

seating position to accommodate a high back child restraint, the

head restraint must be re-installed prior to use of the seat by any other
occupant in order to reduce the risk of personal injury in the event of
a collision.

Check to make sure the child seat is properly secured before each use.
Children 12 and under should be properly restrained in a rear seating
position whenever possible. If all children cannot be seated and
restrained properly in a rear seating position, properly restrain the
largest child in the front seat.

Seating and Safety Restraints

154

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
152
153
154
155
156
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Lancia Страницы: 191

AAB-P-RZR900-K2-001

Бренд: SuperATV Страницы: 3

YARIS LIFTBACK 2009

Бренд: Toyota Страницы: 13

Бренд: Westfalia Страницы: 71

Бренд: Phonocar Страницы: 2

Бренд: Dodge Страницы: 24

Бренд: Flash Cover Страницы: 2

Бренд: EUFAB Страницы: 12

Бренд: Gator Страницы: 8

Бренд: benbat Страницы: 14

Бренд: SPL Страницы: 5

Бренд: Softride Страницы: 4

DH-RB 05.02 Series

Бренд: Dhollandia Страницы: 65

Бренд: Honda Страницы: 7

Бренд: Bazooka Страницы: 2

Бренд: Funkwerk Страницы: 58

Бренд: v.link Страницы: 15

Бренд: Telwin Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды