Mercury 2010 Milan Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 330

background image

Opening the trunk

Press

twice within three seconds to open the trunk.

•

Ensure that the trunk is closed and latched before driving your
vehicle. Failure to properly latch the trunk may cause objects to fall
out or block the driver’s rear view.

Replacing the battery

The integrated keyhead transmitter uses one coin type three-volt lithium
battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin in the slot of the
IKT near the key ring in order to
remove the battery cover.

Note:

Do not wipe off any grease on

the battery terminals on the back
surface of the circuit board.

2. Remove the old battery.

Note:

Please refer to local

regulations when disposing of
transmitter batteries.

3. Insert the new battery. Refer to
the instructions inside the IKT for
the correct orientation of the
battery. Press the battery down to
ensure that the battery is fully
seated in the battery housing cavity.

4. Snap the battery cover back onto
the key.

Note:

Replacement of the battery will

not

cause the IKT to become

deprogrammed from your vehicle. The IKT should operate normally after
battery replacement.

Replacing lost integrated keyhead transmitters (IKTs)

If you would like to have your integrated keyhead transmitters
reprogrammed because you lost one, or would like to buy additional
IKTs, you can either reprogram them yourself, or take

all IKTs

to your

authorized dealer for reprogramming.

Locks and Security

95

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
93
94
95
96
97
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Barker Страницы: 2

Бренд: Ford Страницы: 22

Бренд: Camcar Страницы: 6

Бренд: ABL Страницы: 4

Бренд: Audi Страницы: 9

Бренд: Belkin Страницы: 4

Бренд: MASCOT Страницы: 12

Бренд: Cadillac Страницы: 20

Бренд: MVG Страницы: 18

Бренд: SNIPER Страницы: 2

Бренд: SilverLeaf Electronics Страницы: 16

Бренд: Volvo Страницы: 16

T13 Outback Frontal Protection System

Бренд: T.J.M. Страницы: 18

Бренд: Audi Страницы: 4

Бренд: Crux Страницы: 10

Auto Security AA-9103N

Бренд: Audiovox Страницы: 1

Бренд: travall Страницы: 4

Бренд: Prorack Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды