Mercury 2010 Milan Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 330

background image

POWER WINDOWS

WARNING:

Do not leave children unattended in the vehicle and

do not let children play with the power windows. They may

seriously injure themselves.

WARNING:

When closing the power windows, you should verify

they are free of obstructions and ensure that children and/or

pets are not in the proximity of the window openings.

Press and pull the window switches
to open and close windows.

•

Press down (to the first detent)
and hold the switch to open.

•

Pull up (to the first detent) and
hold the switch to close.

Rear Window Buffeting:

When one or both of the rear windows are

open, the vehicle may demonstrate a wind throb or buffeting noise. This
noise can be alleviated by lowering a front window approximately
2–3 inches (5–8 cm).

One-touch up or down (driver’s window only)

This feature allows the driver’s window to open or close fully without
holding the control down.

To operate one-touch down:

•

Press the switch completely down
to the second detent and release
quickly. The window will open
fully. Momentarily press the
switch to any position to stop the
window operation.

If the switch is pressed and held to
the normal close or one-touch up position during a one-touch down
event, the window will stop. If, after 1/2 second the switch is still held,
the window will perform a normal close or one-touch up.

AUTO

Driver Controls

76

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
74
75
76
77
78
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Honda Страницы: 73

Бренд: ideus Страницы: 159

Бренд: A-Tach Страницы: 2

LED Dominator TAM83S2

Бренд: Whelen Engineering Company Страницы: 2

Crossland X 2017

Бренд: Vauxhall Страницы: 245

PRIME DESIGN HRR3-E-PM52

Бренд: Safe Fleet Страницы: 12

Бренд: Mercedes-Benz Страницы: 493

Бренд: Yenkee Страницы: 22

Бренд: Discount Car Stereo Страницы: 11

Бренд: UCANDAS Страницы: 4

Бренд: U.S. General Страницы: 3

Бренд: TERAFLEX Страницы: 18

Бренд: Camcar Страницы: 6

330e Touring xDrive G21 2021

Бренд: BMW Страницы: 102

2002 Civic Hatchback

Бренд: Honda Страницы: 119

Бренд: Edelbrock Страницы: 1

Бренд: Toyota Страницы: 422

XL-SEAT XLS-DAKC05L

Бренд: ADAPT SOLUTIONS Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды