Mercury 2010 Milan Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 330

background image

WARNING:

When closing the moon roof, you should verify that

it is free of obstructions and ensure that children and/or pets are

not in the proximity of the moon roof opening.

To close the moon roof:

The moon roof is equipped with an automatic, one-touch, express closing
feature. Press and release the front portion of the control. To stop
motion at any time during the one-touch closing, press the control again.

Bounce-back:

When an obstacle has been detected in the moon roof opening as the
moon roof is closing, the moon roof will automatically open and stop at a
prescribed position. This is known as “bounce-back”. If the ignition is
turned off (without accessory delay being active) during bounce-back,
the moon roof will move until the bounce-back position is reached.

Bounce-back override:

To override bounce-back, press and hold the front portion of the control.
For example: Bounce-back can be used to overcome the resistance of ice
on the moon roof or seals. If during a bounce-back condition, the control
is released to the neutral position, then held in the one-touch position
within two seconds after the moon roof reaches the bounce-back
position,

the moon roof will travel with no bounce-back protection.

If the control is released before the moon roof reaches fully closed or the
ignition is turned off (without accessory delay being active), the moon
roof will stop. Security override can be used if the moon roof movement
is restricted in some way, for example, if there is ice on the moon roof or
seals.

To vent:

•

To tilt the moon roof into the vent position (when the glass panel is
closed), press and release the front portion of the control.

•

To close the moon roof from the vent position, press and hold the rear
portion of the control until the glass panel stops moving.

The moon roof has a sliding shade that can be opened or closed when
the glass panel is shut. To close the shade, pull it toward the front of the
vehicle

Accessory delay:

With accessory delay, the window switches, audio system, and moon roof
(if equipped) may be used for up to 10 minutes after the ignition switch
is turned off or until any door is opened.

Driver Controls

84

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
82
83
84
85
86
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Abarth Страницы: 176

Бренд: Daihatsu Страницы: 485

Бренд: Q'STRAINT Страницы: 10

Бренд: Nav TV Страницы: 3

Бренд: PEUGEOT Страницы: 249

2010 Civic Sedan

Бренд: Honda Страницы: 390

Бренд: Boyo Страницы: 9

Бренд: Subaru Страницы: 16

Бренд: v.link Страницы: 12

Бренд: ULTIMATE SPEED Страницы: 34

ZapCharger Portable C1

Бренд: ZAPTEC Страницы: 20

Бренд: Joie Страницы: 53

Бренд: Volvo Страницы: 18

Бренд: Magneti Marelli Страницы: 9

LockNLoad LightenUp

Бренд: Yakima Страницы: 13

Бренд: Hamron Страницы: 6

Follow me RAPID INTRACKER

Бренд: Thule Страницы: 8

Бренд: Boyo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды