Mercury 2010 Milan Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 330

background image

WARNING:

Handle a halogen headlamp bulb carefully and keep

out of children’s reach. Grasp the bulb only by its plastic base

and do not touch the glass. The oil from your hand could cause the
bulb to break the next time the headlamps are operated.

6. Connect the new bulb socket to the electrical connector.

7. Install the new bulb socket into the lamp assembly by aligning the
indexing fingers, then rotate clockwise to the locked position.

8. Install the rubber bulb access cover to the housing.

9. Re-apply pressure around the housing to make sure the protective
rubber cover is completely seated.

10. Turn the headlamps on and make sure they work properly. If the
headlamp was correctly aligned before you changed the bulb, you should
not need to align it again.

Replacing front parking lamp/turn signal bulbs

1. Make sure headlamp control is in the off position, then open the hood.

2. Reach over the front bolster.

3. Remove the bulb socket by
rotating it counterclockwise, then
pull it out of the lamp assembly.

4. Carefully pull bulb straight out of
socket and push in the new one.

5. Install new bulb socket into the
lamp assembly by aligning the
indexing fingers, then rotate
clockwise to locked position.

Lights

65

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
63
64
65
66
67
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Acura Страницы: 2

Бренд: HAUL MASTER Страницы: 8

Бренд: Ford Страницы: 256

Бренд: Skoda Страницы: 165

Бренд: Pyle Страницы: 2

Бренд: Metra Electronics Страницы: 5

Бренд: Renkforce Страницы: 4

Бренд: Mitsubishi MOTORS Страницы: 416

Бренд: Lantronix Страницы: 51

Бренд: Bilstein Страницы: 7

Бренд: Brodit Страницы: 2

Бренд: Toyota Страницы: 285

Бренд: Volvo Страницы: 16

Бренд: Green Valley Страницы: 17

CHALLENGER HELLCAT 2017

Бренд: Dodge Страницы: 484

Бренд: Brodit Страницы: 2

Бренд: Saturn Страницы: 432

Бренд: Westin Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды