Mercury 2010 Milan Скачать руководство пользователя страница 68

Страница: 68 / 330

Replacing high-mount brake lamp bulb

1. Make sure the ignition control is
in the off position.

2. Open the trunk and reach
underneath the package tray to
locate the lamp assembly.

3. Remove the bulb socket by
rotating it counterclockwise, then
pull it out of the lamp assembly.

4. Pull the bulb straight from the
socket and push in the new bulb.

5. Install the bulb socket into the lamp assembly by rotating it clockwise.

Replacing license plate lamp bulbs

1. Make sure the headlamp switch is
in the off position.

2. Remove the screws from the
license plate lamp assembly.

3. Remove bulb socket by turning
counterclockwise.

4. Carefully pull the bulb out from
the socket.

Install new bulb(s) in reverse order.

Replacing fog lamp bulbs

1. Make sure the fog lamp switch is
in the off position.

2. From underneath the vehicle,
partially remove the tire splash
shield by removing four drive
screws.

After removing to allow free access
to the front fog lamp bulb and
electrical wire harness, the splash shield flap can be repositioned.

Lights

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

Содержание 2010 Milan











































































































































































































































































































































Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды

Mercury 2010 Milan, Руководство пользователя

Результаты поиска

Содержание 2010 Milan

Отзывы:

Похожие инструкции для 2010 Milan

Бренды по названию

Популярные бренды