Mercury 2010 Milan Скачать руководство пользователя страница 281 | Manualshive

Страница: 281 / 330

background image

•

2.5L I4 engine

•

3.0L V6 engines

•

Do not overfill the engine with oil. Oil levels above this mark

may cause engine damage.

If the engine is overfilled, some oil must be

removed from the engine by an authorized dealer.

7. Put the dipstick back in and ensure it is fully seated.

On the 2.5L I4 engine, be sure the
notch in the dipstick flange is
aligned with the V on the engine
when it is reinserted.

Adding engine oil

1. Check the engine oil. For instructions, refer to

Checking the engine

oil

in this chapter.

2. If the engine oil level is not within the normal operating range, add only
certified engine oil of the recommended viscosity. Remove the engine oil
filler cap and use a funnel to pour the engine oil into the opening.

3. Recheck the engine oil level. Make sure the oil level is not above the
normal operating range on the engine oil level dipstick.

4. Install the dipstick and ensure it is fully seated.

5. Fully install the engine oil filler cap by turning the filler cap clockwise
until it stops.

To avoid possible oil loss, DO NOT operate the vehicle with the
engine oil level dipstick and/or the engine oil filler cap removed.

Maintenance and Specifications

281

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
279
280
281
282
283
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Wagan Страницы: 8

Бренд: Thermo King Страницы: 2

Бренд: muth Страницы: 10

Бренд: CALIMA Страницы: 9

Бренд: Renault Страницы: 340

Бренд: Audiovox Страницы: 3

Бренд: Victory 4x4 Страницы: 9

Бренд: Caltrend Страницы: 3

Бренд: GARO Страницы: 15

Бренд: SNIPER Страницы: 2

Бренд: Aries Страницы: 5

Бренд: Mercedes-Benz Страницы: 354

Бренд: Havis Страницы: 5

Speed & Route Profiler

Бренд: Racelogic Страницы: 24

Бренд: BrandMotion Страницы: 6

2003 Silhouette

Бренд: Oldsmobile Страницы: 466

Бренд: Mopar Страницы: 18

Бренд: CARFACE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды