Mercury 2010 Milan Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 330

background image

WARNING:

The EPS system has diagnostics checks that

continuously monitor the EPS system to ensure proper operation

of the electronic system. When an electronic error is detected, the
message POWER STEERING ASSIST FAULT will be displayed in the
message center. If this happens, stop the vehicle in a safe place, and
turn off the engine. After at least 10 seconds, reset the system by
restarting the engine, and watch the message center for POWER
STEERING ASSIST FAULT. If the message returns, or returns while
driving, take the vehicle to your dealer to have it checked. With the
message displayed, the steering assist is turned off, making the vehicle
harder to steer.

WARNING:

If the message SERVICE POWER STEERING is

displayed in the message center, the EPS system has detected a

problem with the system function. On the next key cycle the message
SERVICE POWER STEERING NOW will be displayed and steering
assist will be removed until the steering system is serviced. Have your
vehicle taken to the nearest dealer as soon as possible.

If the steering wanders or pulls, check for:

•

an improperly inflated tire

•

uneven tire wear

•

loose or worn suspension components

•

loose or worn steering components

•

improper steering alignment

A high crown in the road or high crosswinds may also make the steering
seem to wander/pull.

Speed sensitive steering

The steering in your vehicle is speed sensitive. At lower speeds the assist
is increased to improve maneuverability.

If the amount of effort required to steer your vehicle changes while
driving at a constant vehicle speed, have the power steering system
checked by your authorized dealer.

Driving

208

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
206
207
208
209
210
...
»

Содержание 2010 Milan











































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Milan

Бренд: Whispbar Страницы: 15

Бренд: TAUBENREUTHER Страницы: 8

Бренд: Thule Страницы: 8

Бренд: A-Tach Страницы: 2

Бренд: ULTIMATE SPEED Страницы: 32

Бренд: Chevrolet Страницы: 441

Бренд: Demco Страницы: 4

Бренд: Subaru Страницы: 540

Бренд: iDataLink Страницы: 6

Бренд: Whispbar Страницы: 63

Бренд: Honda Страницы: 268

Бренд: BMW Страницы: 40

Бренд: Phonocell Страницы: 8

Бренд: Metra Electronics Страницы: 12

Бренд: AUTOTECH Страницы: 2

Бренд: MovaNext Страницы: 4

Бренд: Advent Страницы: 8

Бренд: Stack Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды