Mack E7 Скачать руководство пользователя

Страница: 215 / 303

200 ENGINE ASSEMBLY

Page 6-57

[213 LH] VALVE LIFTER PUSH

RODS

Inspection

Check the push rods. Replace any push rods that

have loose ends, are bent, or show signs of

excessive wear.

Identification

Refer to Figure 6-67.

The current E7 valve lifter has no hole in the

center of the stem. In conjunction with this

change, the E7 inlet and exhaust (nonbrake

engine) push rods have a 0.060-inch (1.524 mm)

maximum flat or dimple on the ball end. The push

rod part number is etched or roll-stamped on the

push rod.

The non-current push rod should be used only

with the non-current lifter. If the non-current push

rod with the wide flat or dimple is used in the

current valve lifter which has no center hole, it

may create an undesirable wear pattern in the

lifter socket.

Mixing current and non-current valve lifters is

permissible when using the correct lifter/push rod

combination.

앫

Current push rod can be used with either

valve lifter.

앫

Do not use non-current valve lifter to service

current valve lifter.

Only Dynatard exhaust push rods are not

affected and can be used with current and non-

current valve lifters. Dynatard intake push rods

still need to be updated to current push rods

when using current valve lifters.

Figure 6-67 — Valve Lifter/Push Rod Identification

200579a

CURRENT 369GC334

NON-CURRENT 369GC329A

PUSH RODS

SMOOTHLY ROUNDED

0.060" MAXIMUM FLAT

OR DIMPLE

WITHOUT

CENTER

HOLE

WITH

CENTER

HOLE

CURRENT 72GC357

NON-CURRENT 72GC347A

0.200" MAXIMUM

FLAT OR DIMPLE

5-101.bk Page 57 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды