Mack E7 Скачать руководство пользователя

Страница: 199 / 303

200 ENGINE ASSEMBLY

Page 6-41

[212 CV] AUXILIARY

DRIVESHAFT

Current production engines (effective February 27,

1992, serial No. 2E1233) feature an improved

“fast ratio” auxiliary driveshaft assembly and oil

pump assembly. This arrangement increases

operating oil pressure by approximately 25% and

creates a change in the oil pump speed. Do not

mix ratios. Refer to Oil Pump assembly

procedures in this section for part number

information.

Inspection

1. Using standard shop procedures, thoroughly

clean auxiliary driveshaft.

2. Inspect auxiliary driveshaft journals, gear

teeth and splines for evidence of cracks,

pitting, scoring or severe wear. Replace

auxiliary driveshaft if any of these conditions

exist.

3. Use magnaflux (PT7190 or equivalent)

inspection procedures to detect cracks.

Installation

앫

Fast Ratio, 1.5:1, part No. 453GC381M

(18 teeth)

앫

Standard Ratio, 1.3:1, part

No. 453GC379AM (17 teeth)

Refer to Figure 6-49.

Purchase the auxiliary driveshaft as an assembly

only. Do not try to dismantle or rework as it may

result in damage to the engine.
It is possible to assemble an auxiliary driveshaft

with a fast ratio oil pump drive gear (5) and a

standard ratio oil pump drive. Do not mix a 1.5

fast ratio assembly with a 1.3 standard ratio

assembly. Damage to the engine will result.

1. Lubricate front auxiliary driveshaft journal

(2), rear auxiliary driveshaft journal (4) and

shaft bearings (in cylinder block) with clean

engine oil.

2. Install shaft (3) into the rear of auxiliary

driveshaft housing. Take care when aligning

shaft through rear bearing (1).

Figure 6-49 — Auxiliary Driveshaft Installation

1. Rear bearing

2. Auxiliary driveshaft front

journal

3. Shaft

4. Auxiliary driveshaft rear

journal

5. Oil pump drive gear

200362a

5-101.bk Page 41 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды