Mack E7 Скачать руководство пользователя

Страница: 253 / 303

200 SETUP AND ADJUSTMENTS

Page 7-13

Accurately setting the injection pump timing is the

best way to ensure optimum fuel economy,

engine durability, and maintain engine exhaust

within established EPA limits.

Special Tools Required

앫

Fixed Timing Position Sensor (Light)

J 37077

앫

Alignment Fixture J 37078

앫

Pump Drive Gear Alignment Dowels

J 37085

앫

Hub Rotation Tool J 38740

Setting Static Fuel Injection Pump
Timing

To set the static fuel injection pump timing, prior

to pump removal, proceed as follows:

1. Remove the TEM sensor (on mechanically

governed engines, remove plug) from the

fixed timing port.

Figure 7-14 — Removing TEM Sensor

Thoroughly clean all residue from the fixed timing

port threads (timing access window) before

installing tool sensor. This will prevent the

possibility of a false reading.

2. Clean all residue from the TEM sensor or

plug threads.

Figure 7-15 — Cleaning TEM Sensor Threads

5-101.bk Page 13 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды