Mack E7 Скачать руководство пользователя страница 169

Страница: 169 / 303

200 ENGINE ASSEMBLY

Page 6-11

[212 NC] CYLINDER SLEEVE

Description

The cylinder sleeve works with the piston, piston

rings, cylinder head, and cylinder head gasket to

seal combustion pressure. It transfers

combustion heat to engine coolant and guides

piston travel during engine operation. Correct

extension of sleeve flange above top deck and

uniform cylinder block counterbore are essential

for satisfactory sleeve life and head gasket seal.

The cylinder sleeves are a wet-dry design, made

of centrifugal cast iron. A crevice seal is needed

for sealing purposes.

Special Tools Required

앫

Depth Gauge J 26948

앫

Dial Bore Gauge J 5347-B

앫

Cylinder Hone and Glaze Breaker J 5902-01

Installation

Refer to Figure 6-12.

1. Thoroughly clean and dry the prepared

cylinder block (6), counterbore ledge (5) and

cylinder sleeves (3). Refer to cylinder block

cleaning procedures in this section.

2. Install the crevice seal (2) into the cylinder

sleeve groove with the pointed face toward

the cylinder block (6) (outward). Lubricate

with ethylene glycol.

3. If the counterbore ledges (5) have been cut,

place the shims (4) on the cylinder block

counterbore ledges. If more than one shim is

necessary, use the fewest number of shims

required to achieve the proper cylinder

sleeve flange height. Always place the

thickest shim on the bottom.

The crevice seal groove (1) must be clean and

free of any oil residue. Under no circumstances

should oil contaminate the crevice seal groove or

crevice seal. Damage to the seal will result.

Applying a Silastic bead is now standard

assembly procedure whenever cylinder sleeves

are installed.
To prevent partial curing and questionable

sealing and bonding, apply Silastic just before

installing the sleeves.

4. Apply approximately a 1/8-inch (3.18 mm)

bead of RTV silicone (Mack Silastic

342SX32, Dow Corning Silastic RTV732, or

General Electric RTV130) around the

cylinder block sleeve seat and completely

around the cylinder wall. Do not use

excessive amounts of RTV.

The cylinder block counterbore ledges and the

cylinder sleeve must be kept clean and free of

any oil residue to ensure that the Silastic bead

seals and bonds properly.

5. Position the cylinder sleeve (3) in the

cylinder bore until it contacts the crevice

seal (2).

6. Placing the palms of the hands on the upper

end of the cylinder sleeve 180 degrees

apart, push downward with a quick, even

pressure. Using a large plastic-faced

hammer, tap the sleeve close to the inside

diameter. Tap alternately from one side to

the other, gradually working around the

entire circumference of the sleeve.

5-101.bk Page 11 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды