Mack E7 Скачать руководство пользователя

Страница: 163 / 303

200 ENGINE ASSEMBLY

Page 6-5

[213 CC] Camshaft Bushings

DESCRIPTION

Lubrication oil is pumped into the cylinder block

main oil gallery. Oil from the gallery flows to each

main bearing bushing bore and then on to the

respective camshaft bushing bore, providing

lubrication for both the crankshaft and camshaft

bushings. Camshaft bushing bores No. 1, 2 and 5

are grooved to supply oil to other components as

well. Oil from the No. 1 camshaft bushing bore

flows on through a drilled passage to lubricate the

front auxiliary driveshaft bushing. Oil from the

No. 2 and 5 camshaft bushing bores flows on

through vertical drilled passages to lubricate the

rocker arm assemblies. Oil from the No. 4

camshaft bushing bore flows through a cast

groove in the cylinder block bushing bore to

lubricate the fuel injection pump, the rear auxiliary

driveshaft bushing, and the air compressor.

INSPECTION

During in-chassis overhaul, check the inside

diameter of the camshaft bushings. If overhauling

out-of-chassis, replace camshaft bushings.

1. Using a telescope gauge or suitable inside

micrometer, measure the ID of each

camshaft bushing in the cylinder block.

Record the dimensions. Refer to Figure 6-4.

Figure 6-4 — Measuring Camshaft Bushing ID

2. Refer to the Fits and Limits chart for

camshaft bushing measurement

specifications. Check the recorded

dimensions against the specifications.

3. If bore size exceeds tolerance or if there is

any evidence of scratching or scoring,

replace the bushings.

REMOVAL

Refer to Figure 6-5.

Use camshaft bushing remover/installer kit

J 37713 (use with J 21428-01 kit) for camshaft

bushing removal.
Camshaft bushings are identified in sequence

from 1 to 7, starting from the front of the engine.

1. Using camshaft bushing remover/installer kit

J 21428-01 (2), with the correct pilot adapter

(J 37713 kit) and a hammer (3), remove the

No. 1 camshaft bushing (4) from the cylinder

block (1).

2. Remove the remaining six bushings in

sequence.

Figure 6-5 — Camshaft Bushing Removal

1. Cylinder block

2. Camshaft bushing

remover/installer

(J 21428-01 kit)

3. Hammer

4. No. 1 camshaft bushing

200319a

5-101.bk Page 5 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды