Mack E7 Скачать руководство пользователя

Страница: 184 / 303

Page 6-26

200 ENGINE ASSEMBLY

Refer to Figure 6-25.

9. Check rod side clearance by installing a

thickness gauge between rod and side of

journal at the entire parting line area.

Figure 6-25 — Connecting Rod Side Clearance Check

10. The clearance must be within specification

shown in the Fits and Limits chart. If not,

recheck for proper cap and rod alignment.

[211 HD] FLYWHEEL HOUSING

Description

Beginning in 1991, flywheel and flywheel

housings for E7 engines equipped with standard

transmissions incorporate engine timing and

engine turnover features. In addition, new

procedures and tools were introduced and must

be used to ensure optimum performance, engine

durability and emission compliance.

Inspection

Inspect the flywheel housing machined surfaces,

capscrews, holes and dowel locations for cracks

or wear. Replace if cracks are evident.

Before installing flywheel housing, examine

crankshaft flange for any cracks, surface damage

or presence of foreign particles. This type of

damage could ruin the sealing capabilities of the

new seal and lead to oil leakage.

Dowel Pins

The diamond locating dowel pins, used to install

the front timing gear cover, flywheel, and flywheel

housing, have been replaced in production by

blade-style locating dowel pins. The diamond

pins were dual-diameter type pins with a smaller

diameter at the round end that goes into the

cylinder block. The blade-style pins are the same

diameter at the round end and the blade end.

There are no changes in the size of the hole in

the flywheel housing. However, the cylinder block

has a larger hole to accept the blade-style dowel

pins. The old cylinder block flywheel housing pin

number is 183GC219 and the new number,

starting with serial No. 2T (August 1992), is

183GC237.

Use a dowel size and type that is appropriate for

the block being used. (Service old with old and

new with new.) Install the blade-style dowel with

the blade in a vertical direction (pointing up and

down).

5-101.bk Page 26 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды