Mack E7 Скачать руководство пользователя

Страница: 147 / 303

200 BENCH PROCEDURES

Page 5-57

When pressure-testing complete oil cooler

assembly using an in-line pressure regulator,

apply pressure at 2–5 psi (14–34 kPa) maximum.

Then gradually increase pressure, checking for

leaks until 80 psi (552 kPa) is reached.

Figure 5-69 — Sealing Oil Outlet

[215 SW] WATER PUMP

The water pump is a belt-driven centrifugal or

impeller type, and is located on the front of the

engine. The water pump pulley is belt-driven by

the crankshaft pulley.

During engine operation, the impeller spins in

proportion to engine speed. The spinning impeller

blades create a negative pressure (suction) at the

water pump inlet port and a positive pressure at

the outlet port. Engine coolant is drawn into the

water pump from the radiator, through the lower

radiator hose. The impeller motion forces coolant

to circulate through the engine block, cylinder

head, and back to the radiator.

To perform water pump service other than

replacement, refer to the COOLING 7.0 manual.

[219 MU] OIL PUMP

The shaft and pumping gear on oil pumps

manufactured after February 1996 are a one-

piece design. Earlier models have a gear

pressed onto a keyed shaft. The shafts are

interchangeable and replacement with a new

(one-piece) shaft is recommended as oil pump

gear-to-housing contact is reduced, resulting in

longer pump life.

Disassembly

Refer to Figure 5-70.

1. Remove pick-up tube and screen assembly

(not shown).

2. Remove oil pump housing cover (7) from oil

pump housing (4).

3. Remove oil pressure relief valve cap (13).
4. Remove oil pressure relief valve spring (12)

and plunger (11).

5. Slide oil pump idler gear (14) off shaft.
6. Turn oil pump upside down and remove oil

pump shaft nut (1) and washer (2).

7. Using a press, remove drive gear (3) and

key (5) from pumping gear and shaft

assembly (6).

8. Remove pumping gear and shaft assembly

from housing.

9. Remove oil pump inlet flange plate (9) and

gasket (8) from housing by removing

capscrews (10).

1. Housing

2. Plate

3. Capscrews

200276a

5-101.bk Page 57 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды