manualshive.com logo in svg

Mack E7, Руководство по обслуживанию

Поделиться
Скачать
Mack E7 Скачать руководство пользователя страница 112

Page 5-22

200 BENCH PROCEDURES

Figure 5-21 — Camshaft Gear Installation

9. Using a suitable press cup, press the gear 

onto the shaft until it is fully seated. The 

pressure gauge on the press should read 

approximately 5 tons (4.54 MT) as the gear 

is being pressed on. As the gear seats, allow 

the pressure to climb to, but not exceed, 

10 tons (9.1 MT). This will ensure that gear 

is seated firmly on shaft. 

10. When gear is properly seated, clearance 

between rear face of gear and thrust washer 

should be between 0.003–0.012 inch 

(0.076–0.305 mm).

11. Thoroughly clean and degrease injection 

pump driving gear with a suitable contact 

cleaner that dries rapidly and leaves no 

residue.

12. Prepare the gear bore surface with 

Locquic™ Primer T, or equivalent.

13. Apply a bead of Loctite 609, or equivalent, to 

the gear bore.

14. Using a clean brush, spread Loctite 609 

evenly on the entire surface of the gear 

bore.

15. Position gear onto camshaft.
16. Using a suitable press cup, press the gear 

onto the shaft until it is fully seated. The 

pressure gauge on the press should read 

approximately 5 tons (4.54 MT) as the gear 

is being pressed on. As the gear seats, allow 

the pressure to climb to, but not exceed, 

10 tons (9.1 MT). This will ensure that gear 

is seated firmly on shaft. The gear should be 

flush with the end of the shaft when fully 

seated. 

Figure 5-22 — Fuel Injection Pump Driving Gear 

Installation

[213 EV] CYLINDER HEADS

Description

Refer to Figure 5-23.

The cylinder heads featured on 1991 and later E7 

engines incorporate internal design modifications 

that increase the swirl level of combustion air. To 

achieve the increase in air motion required, it was 

necessary to redesign the inlet port. Increased air 

motion, in conjunction with the eight-hole Valve 

Covering Orifice (VCO) nozzle tips, provides 

proper air/fuel atomization in the deeper bowl of 

the piston crown. 

1991 and later E7 cylinder heads are NOT 

interchangeable with 1989/1990 E7 cylinder 

heads. 

5-101.bk  Page 22  Friday, March 17, 2006  11:05 AM

Содержание E7
















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды