Mack E7 Скачать руководство пользователя

Страница: 217 / 303

200 ENGINE ASSEMBLY

Page 6-59

[213 LP] ROCKER ARMS

Description

The valve rockers pivot on a shaft supported by

three brackets per cylinder head. Two capscrews

secure each bracket to the cylinder head. The

rocker arms are operated by a camshaft through

valve lifters and push rods extending through the

cylinder heads. A coil spring returns each valve to

the closed position, holding the rocker arm in

contact with the push rod.

Installation (Non-Brake and
Dynatard Equipped Engines)

Refer to Figure 6-69.

1. Position the rocker arm assemblies on the

cylinder heads.

2. Ensure that the ball end of the rocker arm

adjusters are in position in the push rod

cups.

Make sure that adjusting screws are retracted

upward in the rocker arms. If extended far below

rocker arm, the push rods can be bent when

tightening the rocker arm assembly brackets.

3. Lubricate the threads of the rocker arm

mounting capscrews with clean engine oil.

Install the capscrews and torque to 40 lb-ft

(54 N

폷

m) using torque wrench J 24407 or

equivalent.

4. Adjust valve and engine brake slave piston

lash settings as applicable. Refer to the

SETUP AND ADJUSTMENTS section in this

manual for correct specification.

Figure 6-69 — Valve Rocker Arm Installation

Installation (Jake Brake-Equipped
Engines)

Use only Jacobs exhaust rocker arm adjusting

screws for Jacobs engine brake installation.

Using a MACK or any other type of screw will

result in severe screw wear and engine damage.

Jacobs exhaust rocker screws have hex heads.

MACK screws have a screwdriver slot.

Refer to Figure 6-70.

Verify that Jacobs exhaust rocker arm adjusting

screws are installed in the exhaust rocker arms.

Turn the screws all the way into the rocker arms

from the underside. Install the MACK locknuts.

1. Install the rocker arm assemblies. Apply

clean engine oil to the MACK hold-down

capscrews. Install one capscrew with a

washer in each bracket next to the push

rods. Each rocker assembly has three

brackets.

5-101.bk Page 59 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды