Mack E7 Скачать руководство пользователя

Страница: 83 / 303

200 ENGINE DISASSEMBLY

Page 4-25

Figure 4-30 — Camshaft Thrust Washer Capscrews

Refer to Figure 4-31.

3. Install the camshaft removal/installation tool

J 41461 (3) in position on the rear segment

of the camshaft (1), securing it with the clip

(2) to the shaft.

Figure 4-31 — Camshaft Removal/Installation Tool

4. Taking care not to damage camshaft or

bushings, pull camshaft out of the front of

the engine. Carefully guide rear of shaft

through the journals. If shaft does not come

out freely, ensure all valve lifters are clear of

camshaft cams and journals.

5. Remove valve lifters.

Valve lifters have established wear patterns and

should be reinstalled in same locations. Label

each valve lifter upon removal and place on a

clean work surface.

[212 NP & LQ] PISTON AND

CONNECTING ROD ASSEMBLY

The crankshaft and related components are

heavy, have sharp edges and many possible

pinch points. Always be careful while working

in this area to avoid serious personal injury.

Before removing pistons, connecting rods and

rod caps, ensure they are marked so they can be

reinstalled in the same cylinders from which they

were removed.

Remove connecting rod and piston assemblies in

companion cylinder sets: 1 and 6, 2 and 5, and 3

and 4.

1. Rotate engine stand 90 degrees so that

pistons lie horizontally in the block with top

of pistons and connecting rods accessible.

2. Rotate crankshaft so that pistons 1 and 6

are lowered in the cylinder at least

two inches (51 mm) to allow adequate room

to remove carbon from upper edge of

sleeves.

1. Thrust washer

2. Openings

3. Capscrew, 12-point

4. Camshaft drive gear

1. Rear segment of

camshaft

2. Tool retaining clip

3. Camshaft removal/

installation tool

200365a

200573a

5-101.bk Page 25 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды