Mack E7 Скачать руководство пользователя

Страница: 157 / 303

200 BENCH PROCEDURES

Page 5-67

[222 KG] INJECTOR NOZZLES

1991 and later MACK E7 engines require

different fuel injection nozzles, nozzle holders

and nozzle holder assemblies than previous E7

engines.

These later nozzles (with eight spray holes) are a

Valve Covering Orifice (VCO) configuration and

are hydroground for proper fuel flow and

atomization.

Nozzles used for 1989/1990 MACK E7

production engine models feature six spray holes

and are not hydroground.

These parts are not interchangeable with eight-

spray-hole nozzles used in 1991 and later

engines. Refer to the following engine tune-up

publications for pertinent E7 specifications.

5-301............................. 1989

5-302............................. 1990

5-303............................. 1991

5-304............................. 1992

5-305............................. 1993

5-306............................. 1994

5-307............................. 1995

5-308.................... 1996/1997

Nozzle Cleaning

When servicing nozzle holder assemblies,

cleaning of nozzle tips may be necessary.

Special care must be taken when cleaning nozzle

tips to avoid damaging nozzle spray holes.

앫

Preferred cleaning method: ultrasonic

cleaning

앫

Acceptable cleaning method: brass brush/

wire wheel

ULTRASONIC CLEANING METHOD

Ultrasonic cleaning units such as J 29653-A, use

sound waves or mechanical vibrations,

approximately 55,000 cycles per second above

human hearing range. Sound waves are

generated by the transducer, which changes

high-frequency electrical energy into mechanical

energy.

The nozzles will be damaged if a steel-wire wheel

is used for cleaning. Damage can also occur if an

improper size and/or speed of brass-wire wheel is

used.

5-101.bk Page 67 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды