Mack E7 Скачать руководство пользователя

Страница: 264 / 303

Page 8-2

200 ENGINE INSTALLATION & TESTING

INSTALLATION

Description

Engine installation details vary from vehicle to

vehicle. The following procedure provides

general installation guidelines for MACK E7

engines.

It is good practice to steam-clean road grime,

grease, and oil from the engine before service.

Steam-cleaning the engine and engine

compartment permits more detailed inspection

and improved workmanship.

Before beginning, make sure all equipment has

been inspected for safety and is available for use.

Place vehicle on a flat, level surface. Make sure

area has ample work space.

Newly designed torsional idler-gear assemblies

are now available for servicing both 1:1 and 0.7:1

ratio Flywheel Power Take-Off (FWPTO) units in

E7 engines equipped with a T200 series

transmission and FWPTO. New assemblies

feature a two-piece idler gear and torsion spring.

The new torsional idler-gear assembly reduces

spline wear on the FWPTO input (drive) gear. If

the unit is removed for any reason:

앫

Inspect input gear splines for excessive wear.

앫

If splines show excessive wear, disassemble

the FWPTO far enough to gain access to

idler-gear assembly. Refer to MACK Service

Manual 10-901, Flywheel Power Take-Off.

Removing Engine from Engine
Stand

1. Attach a suitable lifting device to lifting points

on engine.

2. Position and attach an engine hoist to lifting

device; place tension on the device by

operating hoist.

3. With lifting device supporting the engine

weight, remove mounting capscrews from

engine stand.

Engine Installation into Vehicle

Obtain assistance when installing the engine. Be

sure to watch for obstructions such as engine or

chassis components, brackets, clamps or other

components that may interfere with engine

installation.

1. Align engine with torque converter or clutch

(as applicable) and install transmission bell

housing to the flywheel housing capscrews.

Torque to specification.

2. Install engine mount capscrews to secure

engine mounts to engine. Torque to

specification.

3. Remove transmission jack from under

transmission.

4. Install clutch linkage and bracket-retaining

capscrews.

5. Install power-steering hoses and reservoir, if

applicable.

6. Install hood rest crossmember(s), if

applicable.

7. Install exhaust bracket to flywheel housing

and exhaust clamp at turbocharger.

8. Install starter. Connect wiring and cables.
9. Install air cleaner housing, if required.

10. Install all coolant tubes, ground straps, air

lines, fuel lines, hydraulic hoses or tubes,

throttle linkage and electrical wiring

harnesses that were removed from engine

during removal.

On some E7 models, the machined V-band was

replaced with a 3.5-inch push-on turbocharger

discharge connection that is angled forward.

The remaining models use a 3-inch push-on

connection directed 90 degrees outward from

the center line of turbocharger.

5-101.bk Page 2 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды