Mack E7 Скачать руководство пользователя страница 183

Страница: 183 / 303

200 ENGINE ASSEMBLY

Page 6-25

Do not force the piston. This indicates an

incorrectly aligned ring. Remove piston, correct

the problem, and reinstall.
Before pushing piston all the way down in the

sleeve, check to see if piston cooling nozzle is

aligned with the nozzle clearance notch provided

in the lower end of the piston skirt. If it is not

aligned, damage to piston or spray nozzle may

result.

13. Align rod with the journal and continue

pushing piston into sleeve while guiding rod

end (to clear piston cooling nozzle), until rod

is in position on the crankshaft journal.

14. Ensure that the correct mate to the upper

rod bearing and alignment sleeves, if

applicable, are positioned in the rod cap.

Perform a running clearance check at this

connecting rod journal before installing the

next piston in Step 15.

Perform running clearance check after installing

each piston. Damage to engine may result if

clearance is not within specification.

15. After performing running clearance check,

repeat above installation procedures to

install the No. 6 piston.

16. Rotate crankshaft so that the journals for the

No. 2 and No. 5 cylinders are at bottom dead

center. Follow above installation procedures

to install the No. 2 and No. 5 pistons. Repeat

procedures to install the No. 3 and No. 4

pistons.

CHECKING RUNNING CLEARANCE

1. Place a section of Plastigage on the cap

bearing and assemble cap to rod.

2. Apply a light coat of oil on threads of the rod

cap capscrews and secure cap.

3. Torque capscrews to 150 lb-ft

(203 N

폷

m) using torque wrench J 24407 or

equivalent.

4. Remove capscrews and cap, and check the

bearing running clearance.

5. Using a Plastigage width chart, measure

width of the Plastigage and remove it from

bearing.

6. If clearance is not within specification,

correct as required. Make sure to use the

correct size bearing.

7. If clearance is less than specified, also

check behind bearing for dirt, chips or burrs

which would prevent the bearing from

seating properly.

8. Reposition cap on journal. Lubricate new

capscrews with clean engine oil, install the

capscrews and torque to 150 lb-ft

(203 N

폷

m) using torque wrench J 24407 or

equivalent.

If cap and rod are not properly aligned, bearing

and rod damage may result.

5-101.bk Page 25 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды