Mack E7 Скачать руководство пользователя

Страница: 141 / 303

200 BENCH PROCEDURES

Page 5-51

At this point, a used or scrapped cylinder head

can be used as a template for proper bracket

alignment and to ensure mounting surfaces of

each bracket are parallel.

12. Lubricate inlet rocker arm (3) and install on

shaft.

13. Assemble rocker arm retaining (coil) spring

(6) on shaft.

14. Lubricate exhaust rocker arm (5) and install

on shaft.

15. Place last (third) rocker arm shaft bracket (4)

and shaft on a flat surface. This bracket

does not have a threaded hole on top or an

oil hole at bottom surface. Align mounting

surface of bracket and offset with two

brackets already installed.

16. Check for proper bracket alignment. Ensure

that mounting surfaces of each bracket are

parallel. Press shaft into rocker arm bracket.

17. Lubricate and install outermost inlet rocker

arm (3).

18. Install flat spring and retaining snap ring on

end of shaft to keep inlet rocker arm in

place.

19. At opposite end of shaft, lubricate and install

outermost exhaust rocker arm (5).

20. Install flat spring (2) and snap ring (1) on end

of shaft to keep rocker arm in place. Some

rocker arm shafts are equipped with

threaded plugs and aluminum washers

instead of flat springs and snap rings.

21. Check all rocker arms to make sure they

rotate freely.

Dynatard Engine Brake Solenoid

Refer to Figure 5-64.

1. On valve rocker arm shaft assemblies

with a Dynatard engine brake, install

solenoid mounting adapter seal (O-ring) in

counterbore in rocker shaft.

2. Lubricate solenoid mounting threads with

clean engine oil.

Figure 5-64 — Solenoid Mounting Adapter O-Ring

Refer to Figure 5-65.

3. Assemble solenoid mounting adapter

into shaft and torque to 23–25 lb-ft

(31–34 N•m) with crows-foot adapter and

a calibrated torque wrench (J 24406 or

equivalent).

Figure 5-65 — Dynatard Engine Brake Solenoid

Installation

[266 KD] DYNATARD ENGINE

BRAKE

Dynatard Overload Protection
(E7 Engines with Dynatard)

E7 engines built after January 1, 1992 and

through mid-year 1993 are equipped with a

Dynatard overload protection system. From mid-

year 1993 through December 1993, E7 engines

were built with either the Dynatard system or a

Jake Brake

. Mack Trucks, Inc. recommends

installing the Dynatard overload protection

system on all E7 engines built prior to

January 1, 1992. This system consists of a

5-101.bk Page 51 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды