Mack E7 Скачать руководство пользователя

Страница: 214 / 303

Page 6-56

200 ENGINE ASSEMBLY

4. Insert nozzle holder in the nozzle holder

hole. Be sure to align the locator ball in the

nozzle holder with the socket in the cylinder

head to ensure inlet tube alignment. Refer to

Figure 6-63.

Figure 6-63 — Nozzle Holder Alignment

5. After making sure that the nozzle holder ball

is properly aligned with the alignment socket

in the cylinder head, push downward on the

handle of the installation tool driving the

nozzle holder into position. Refer to

Figure 6-64.

Figure 6-64 — Nozzle Holder Installation

6. Remove the tool from the nozzle holder and

insert the gauge block on the end of the tool

handle.

7. Insert the gauge block into the nozzle holder

hole. The gauge block should be flush with

the top of the cylinder head surface. Refer to

Figure 6-65.

앫

If the gauge block is below level, it may

indicate that the gasket was omitted.

앫

If the gauge block is too high, it may

indicate that there are two gaskets

installed under the nozzle holder, or the

nozzle holder has not been fully inserted.

앫

If a gauge block is not available,

measure the distance from the top of the

cylinder head to the top of the nozzle

holder. The nominal measurement

should be 0.564 inch (14.326 mm).

Figure 6-65 — Nozzle Holder Installation Check

8. Lubricate the threads of the retaining plug

and install in position. Torque to 45 lb-ft

(61 N

폷

m) using torque wrench J 24407 or

equivalent. Refer to Figure 6-66.

Figure 6-66 — Retaining Plug Installation

1. Nozzle holder puller

J 37093

2. Gauge block

5-101.bk Page 56 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды