Mack E7 Скачать руководство пользователя страница 268

Страница: 268 / 303

Page 8-6

200 ENGINE INSTALLATION & TESTING

[233 FA] CHASSIS-MOUNTED

CHARGE AIR COOLING

Description

The Chassis-Mounted Charge Air Cooling

(CMCAC) system cools hot turbocharged air

before it enters the engine intake manifold. The

CMCAC system uses ambient air as a cooling

medium by allowing it to pass through a core

equipped with heat-exchanging fins.

Hot turbocharged air, varying in pressure from

0.0–25 psi (0.0–172 kPa), passes through core

tubes where heat is transferred to the ambient air

by heat-exchanging fins.

Front-section core construction consists of a

series of cold bars, cold fins and tube plates.

Side-section core construction consists of a

series of hot bars and hot fins.

Special Tool Required

앫

Charge Air Cooler Pressure Fixture J 41473

CMCAC Troubleshooting

205217

Symptom

Probable Cause

Remedy

Normal Boost — High Pyrometer

1. Core fin obstructions.

1. Clean core fins.

Low Boost — High Pyrometer

1. Restriction in ducting between air

cleaner and turbo.

1. Check for blockage and clean.

2. Dirty turbocharger.

2. Clean turbocharger.

3. Leaks in the pressurized side of the

induction system.

3. Check for and repair leaks.

4. Inlet manifold leak.

4. Check for loose or missing fittings,

plugs, and/or damaged manifold-to-

cylinder head gaskets. Replace missing

parts, and repair loose connections.

5. Open petcock (if equipped).

5. Close petcock.

6. Core leakage.

6. Pressure test core. Remove, repair or

replace core if test results are not

satisfactory.

Low Power

1. Restrictions in cooler.

1. Perform restriction pressure test. Clean

out restriction.

2. Restrictions in cooler inlet and outlet

tubes.

2. Disconnect and clean obstructions.

5-101.bk Page 6 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Бренды по названию

Популярные бренды