Mack E7 Скачать руководство пользователя

Страница: 154 / 303

Page 5-64

200 BENCH PROCEDURES

Cleaning and Inspection

1. Thoroughly clean inner sleeve and inner

shaft with solvent and dry with compressed

air.

2. Inspect inner sleeve and inner shaft for

extreme wear, cracks or other damage.

Replace as necessary.

3. Inspect outer shaft drive hub and seals.
4. Inspect Econovance housing.

Econovance Assembly

1. Using clean engine oil, lubricate all gear

surfaces.

2. Install Econovance spring (3) on inner shaft

assembly (2).

Make sure spring is properly seated. If not,

binding will occur, causing damage to

Econovance assembly.

3. Reinstall inner sleeve (4) on inner shaft

assembly. Push down on inner sleeve until

flush with lower seat. To accomplish this,

spring must be properly seated. Make sure

sleeve does not bind on shaft.

4. Reinstall inner sleeve and inner shaft

assembly into outer shaft drive hub. Install

outer shaft drive hub into Econovance outer

housing (8), using new seal if needed.

5. Reinstall retainer ring (1) in rear of

Econovance assembly.

6. Apply Loctite 242 to drive-hub retaining

capscrew (10) threads.

Grooved side of hub retaining capscrew washer

must face outer shaft drive hub (5).

Refer to Figure 5-76.

7. Install outer shaft drive-hub retaining

capscrew (10) and washer (9). Torque to

150 lb-ft (203 N•m) using torque wrench

J 24407 or equivalent.

Figure 5-76 — Drive Hub Installation

[221 KU] INJECTION PUMP

DRIVE HUB

Description

For mechanically governed engines, a scalloped-

type drive hub is installed directly on the fuel

injection pump camshaft. For V-MAC engines,

the outer shaft drive hub, along with inner sleeve,

spring and inner shaft assembly, is part of the

Econovance unit. It is linked to the fuel injection

pump with a Celeron coupling or a two-piece

metal-type coupling, depending on the date of

production.

Special Tools Required

앫

Pump Holding Fixture J 37078

앫

Injection Pump Drive Coupling Holder

J 28452-A

5-101.bk Page 64 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды