Mack E7 Скачать руководство пользователя

Страница: 216 / 303

Page 6-58

200 ENGINE ASSEMBLY

All E7 production engines starting with serial

No. 2X0000 and above, feature valve lifters with

no hole as well as inlet and nonbrake push rods

with 0.060 inch (1.524 mm) maximum flat or

dimple on the push rod ball end.

Installation

Used push rods have established wear patterns.

Push rods being returned to service should be

installed in the same position from which they

were removed.

1. Apply lubricating oil to spherical end of the

push rod and insert it into the lifter opening.

Ensure that it has engaged the lifter by lifting

it slightly. If the lifter has been properly

contacted, some resistance will be felt in the

rod as the lifter is raised.

2. Repeat step 1 until all 12 push rods are in

position.

[213 NV] VALVE YOKES

Description

There are two exhaust valves and two inlet valves

for each cylinder. Each rocker arm, in conjunction

with the valve yoke, operates both valves

together, in a set (exhaust or inlet), per cylinder.

Installation

Used yokes have established wear patterns.

Yokes being returned to service should be

installed in the same position from which they

were removed.

Refer to Figure 6-68.

1. Lubricate the yoke guide pins (5) with clean

engine oil.

If the engine is equipped with a Jake Brake, the

exhaust valve yokes will have a larger rocker arm

contact surface. The yokes with the larger

surface must be installed on pins corresponding

with the Jake Brake actuators.

2. Place the valve yokes (2) on the yoke guide

pins from which they were removed. Slightly

rock the yokes from side to side to be sure

they are seated on the valve stems (4).

Engines equipped with Jake Brake: Effective

January 1994 (engine serial No. 401269), the

E7 Jake Brake yoke was manufactured with

metric threads utilizing the Spiralock™ thread

form. Refer to Section 7, SETUP AND

ADJUSTMENTS, under Valve Yoke, Valve Lash

and Slave Piston Adjustments (with Jake Brake)

for details regarding correct method to loosen the

yoke adjusting screw.

Figure 6-68 — Valve Yoke

1. Rocker arm

2. Valve yoke

3. Yoke adjusting screw

4. Jam nut

5. Valve stem

6. Yoke guide pin

5-101.bk Page 58 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды