Mack E7 Скачать руководство пользователя

Страница: 99 / 303

200 BENCH PROCEDURES

Page 5-9

Figure 5-6 — Connecting Rod Fixture

Maximum twist of connecting rod within 12 inches

(30.5 cm) is 0.010 inch (0.254 mm). The

maximum bend of connecting rod within

12 inches (30.5 cm) is 0.004 inch (0.102 mm).

Distances are center to center.

[212 HP] CRANKSHAFT

Description

The crankshaft is fully counterbalanced and

journals are induction-hardened. There are seven

main bearings. Thrust washers located at the

center main bearing (position No. 4) absorb fore

and aft end thrust. Crankshaft extension at

forward end carries the main drive gear, vibration

damper and accessory drive pulleys. The main

drive gear has a shrink fit and the vibration

damper hub has a press fit. The main drive gear

is keyed to the crankshaft and proper assembly is

important for engine timing. The flywheel is

mounted to a flange at rear of crankshaft. Two

seals, one at the front and one at the rear,

prevent engine lubricating oil from leaking around

ends of the crankshaft.

Bearing caps are furnished with the crankcase

and support the crankshaft in true alignment.

Webs integral to the crankcase provide upper half

of main bearing supports. Removable caps

provide lower support. Capscrews hold the

caps in position. The bearing caps are not

interchangeable and each has a number stamped

on it which signifies its correct location and

alignment in the crankcase. The caps are

numbered 1 through 7, with No. 1 main bearing

cap in front of engine. The bearing inserts are

precision designed. Bearings are inserted

between the crankshaft and crankcase, and

between the crankshaft and bearing caps. Thrust

flanges to support thrust washers are located at

the center main bearing (No. 4).

Extreme care must be taken to guarantee

cleanliness of crankcase, crankshaft, and

bearings during servicing and after service has

been completed. Whenever possible, crankshaft

should be removed when bearings are being

installed in order to clean crankcase thoroughly.
All bearing surfaces must be free of grit and

burrs. Small particles of dust and dirt left between

crankshaft and bearings will cause rapid wear

and scoring of crankshaft journal and inserts. Any

foreign material left between bearings and

crankshaft bearing caps will cause distortion of

bearing and a reduction in operating clearance at

that point. The resulting frictional heat will cause

bearing material to melt away from steel backing

of bearing at that point. Such melted material will

create further hot spots until complete bearing

failure occurs. Anything that interferes with

operating clearance of any bearing, or proper

heat dissipation, affects bearing life. Cleanliness

cannot be overstressed.

200329a

5-101.bk Page 9 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды