Mack E7 Скачать руководство пользователя

Страница: 27 / 303

200 GENERAL INFORMATION

Page 1-3

ENGINE MODEL

IDENTIFICATION

Engine Information Plate

All engines are identified by an engine

information plate located on the front valve cover

of the engine. This plate indicates the engine’s

11GBA number, emission standards, serial

number and various engine adjustments. The

engine is also identified by the serial number

stamped into the cylinder block above the timing

cover on early engines, or on the pad just to the

rear of the air compressor on later engines.

For some current MACK engines, the engine

information plate also includes pertinent

emissions characteristics of NO

and particulates

unique to that engine.
A given MACK engine may meet federal emission

regulations in 49 states (excluding California) or

an engine may meet emission regulations of all

50 states (including California). To determine

which regulations a given engine meets, refer to

the engine information plate. If the engine plate

has a series of dashes in the long upper-left

block, and two dashes in the CALIF. FAMILY

block, the engine does not meet California

regulations.

Figure 3 — Engine Information Plates

New Engine Information Plate

The following explanations are provided to aid in

interpreting some of the key information found on

the new engine information plate (effective late

1996). Refer to Figure 1-4.

Block 1 — U.S. EPA Regulations

앫

An “X” in block one means the engine meets

United States EPA regulations for the year

stamped in block No. four.

앫

Two dashes in block one indicates the

engine does not meet United States EPA

regulations for the year stamped in block

No. four. This is only permissible with certain

export engines. All domestic engines will

have an “X” in block one.

Block 2 — California Regulations

앫

An “X” in block two indicates the engine

meets California emissions regulations for

the year stamped in block No. four. This

engine is referred to as a “50-state” engine

and can be sold in any state throughout the

U.S.

앫

Two dashes stamped in block two means

the engine does not meet California

emissions regulations. If an engine has an

“X” in block one and two dashes in block

two, it is referred to as a “49-state” engine,

meaning it is not certified for sale in

California.

5-101.bk Page 3 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды