Mack E7 Скачать руководство пользователя

Страница: 222 / 303

Page 6-64

200 ENGINE ASSEMBLY

[215 NK] COOLANT MANIFOLD

Inspection

Check the coolant manifold sections for

restrictions, cracks and flange wear. The manifold

cannot be repaired. Replace if any signs of

damage are present.

Installation

Refer to Figure 6-74.

1. Ensure that the front coolant manifold

section (1) is clean. Position a coolant/air

inlet manifold gasket on the mounting

surface.

2. Lubricate threads of the capscrews (5) with

clean engine oil and secure front coolant

manifold section with the mounting

capscrews.

3. Place couple (2) in position on the couple

mounting flange. Place two clamps (3) over

the couple.

4. Insert the rear manifold section (4) in the

couple.

5. Place a gasket between the mounting

surfaces of the rear manifold section and the

cylinder head.

6. Lubricate threads of the mounting

capscrews (5) and secure the rear manifold

section with the mounting capscrews.

7. Torque all mounting capscrews to 25 lb-ft

(34 N

폷

m) using torque wrench J 24406 or

equivalent.

8. Ensure that the couple is properly installed

and secure it in position with the clamps.

Tighten the clamps to 38 lb-in (4.3 N

폷

m).

Figure 6-74 — Coolant and Air Inlet Manifold Installation

200251a

1. Coolant manifold, front section

2. Couple

3. Clamp

4. Coolant manifold, rear section

5. Capscrew

6. Air inlet manifold, rear section

7. Inlet air temperature sensor (sending unit)

8. Air inlet manifold, front section

9. Capscrew, 12-point

5-101.bk Page 64 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды