Mack E7 Скачать руководство пользователя

Страница: 228 / 303

Page 6-70

200 ENGINE ASSEMBLY

[222 KD] FUEL NOZZLE INLET

TUBE ASSEMBLY

Installation

Refer to Figure 6-88.

1. Install the fuel nozzle inlet tube assemblies

(1) into the front and rear cylinder heads.

Lubricate the nozzle inlet tube clamping

screw threads before installing.

2. Install the tube assemblies until light contact

is made with the nozzle holders. Lightly

tighten the clamping screws and then lightly

tighten the fuel inlet tube sleeve nuts (1).

3. Connect the injection pump end of the fuel

tubes to the appropriate fuel injection pump

outlet ports and lightly tighten the sleeve

nuts (6).

4. Install and lightly tighten the fuel inlet tube

insulators and clamp plate and brackets (3).

These tube insulators and clamp plates and

brackets are required to prevent cavitation

erosion and vibration failure of the tubes.

5. Tighten all fuel inlet tube assembly clamping

screws to 35 lb-ft (48 N

폷

m) torque using

torque wrench J 24407 or equivalent.

An open-ended “crow’s foot” adapter is required

with the torque wrench for installation of nozzle

fuel inlet tube assemblies. Avoid twisting the lines

when tightening the sleeve nuts.

6. While holding the fuel inlet tube assembly

clamping screws, tighten the tube sleeve

nuts (1) at the cylinder heads to 25 lb-ft

(34 N

폷

m) torque using torque wrench

J 24407 or equivalent

7. Tighten all fuel inlet tube sleeve nuts (6)

located at the fuel injection pump outlet ports

to 25 lb-ft (34 N

폷

m) torque using torque

wrench J 24407 or equivalent.

8. Tighten all fuel inlet tube insulators and

clamp plates and brackets.

5-101.bk Page 70 Friday, March 17, 2006 11:05 AM

Содержание E7
















































































































































































































































































































Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды

Mack E7, Руководство по обслуживанию

Результаты поиска

Содержание E7

Отзывы:

Похожие инструкции для E7

Бренды по названию

Популярные бренды