Lenovo HX1310 Скачать руководство пользователя страница 784

Страница: 784 / 1002

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-2004ffff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 4)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c2004ffff or 0x816f070c2004ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0127

User Response

No action; information only.

•

816f070c-2005ffff : Configuration error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]has deasserted. (DIMM 5)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has deasserted.

May also be shown as 816f070c2005ffff or 0x816f070c2005ffff

Severity

Info

Serviceable

Automatically notify support

770

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды