manualshive.com logo in svg

Lenovo HX1310, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo HX1310 Скачать руководство пользователя страница 499

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - CPU

SNMP Trap ID

40

CIM Information

Prefix:

PLAT

ID:

0062

User Response

1. Check the CPU LED. See more information about the CPU LED in Light path diagnostics.

2. Check for a server firmware update. Important: Some cluster solutions require specific code

levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest
level of code is supported for the cluster solution before you update the code.

3. Make sure that the installed microprocessors are compatible with each other.

4. (Trained technician only) Reseat microprocessor n.

5. (Trained technician only) Replace microprocessor n. (n = microprocessor number)

One of the CPUs :

•

806f050c-2001ffff : Memory Logging Limit Reached for [PhysicalMemoryElementName] on

Subsystem [MemoryElementName]. (DIMM 1)

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Reached.

May also be shown as 806f050c2001ffff or 0x806f050c2001ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Warning - Memory

SNMP Trap ID

43

CIM Information

Prefix:

PLAT

ID:

0144

Appendix A. Integrated management module 2.1 (IMM2.1) error messages

485

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды