Lenovo HX1310 Скачать руководство пользователя страница 178

Страница: 178 / 1002

Align the installation tool with the microprocessor socket. The installation tool rests flush on
the socket only if properly aligned.

Figure 93. Installation tool alignment

Install the microprocessor using the following instructions for your installation tool.

• When using the installation tool, twist the handle of the installation tool assembly

counterclockwise until the microprocessor is inserted into the socket, and lift the installation
tool out of the socket.

Handle

Installation tool

Microprocessor

Figure 94. Installation tool handle adjustment

164

HX1310, HX2310-E, HX3310, HX3310-F Installation and Service Guide

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды