Lenovo HX1310 Скачать руководство пользователя страница 37

Страница: 37 / 1002

Video
connector

Ethernet
connector 4

Ethernet
connector 2

Ethernet
connector 3

Ethernet
connector 1

USB 3.0
connector
(connector 2)

USB 3.0
connector
(connector 1)

System-management
Ethernet connector
(dedicated)

Figure 15. System-board external connectors

System-board switches, jumpers, and buttons

The following illustration shows the location of the switches, jumpers, and buttons on the server.

Important:

• Before you change any switch settings or move any jumpers, turn off the server; then, disconnect all

power cords and external cables. Review the information in “Safety” on page v, “Installation guidelines”
on page 100, “Handling static-sensitive devices” on page 102, and “Turning off the server” on page 27.

• Any system-board switch or jumper block that is not shown in the illustrations in this document are

reserved.

• If there is a clear protective sticker on the top of the switch blocks, you must remove and discard it to

access the switches.

Chapter 1

The Lenovo Converged HX Series server

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Похожие инструкции для HX1310

Бренды по названию

Популярные бренды