Lenovo HX1310 Скачать руководство пользователя страница 153

Страница: 153 / 1002

Step 5.

Locate the coin-cell battery on the system board.

Coin-cell battery

Figure 61. Location of the coin-cell battery on system board

If there is a rubber cover on the battery holder, use your fingers to lift the battery cover from
the battery connector.

Use one finger to tilt the battery horizontally out of its socket, pushing it away from the socket.

Attention:

Neither tilt nor push the battery by using excessive force.

Figure 62. Coin-cell battery removal

Use your thumb and index finger to lift the battery from the socket.

Attention:

Do not lift the battery by using excessive force. Failing to remove the battery

properly may damage the socket on the system board. Any damage to the socket may require
replacing the system board.

Chapter 5

Removing and replacing components

139

Содержание HX1310











































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX1310, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX1310

Отзывы:

Бренды по названию

Популярные бренды